How to Turn the intpw 9‑Port USB 3.2 Hub into Your Home‑Office Backup Hub

How to Turn the intpw 9‑Port USB 3.2 Hub into Your Home‑Office Backup Hub


Yes – the intpw 9‑Port USB 3.2 Hub can serve as a reliable central hub for automated backups in a home‑office environment. Its mix of USB‑C and USB‑A ports, 10 Gbps transfer speeds, and a dedicated 65 W power adapter let you plug in several external hard drives and keep them powered while your computer runs scheduled backup jobs. Below is a practical workflow that takes you from plugging the hub into your workstation to setting up a “set‑and‑forget” backup routine.

Why a Dedicated Hub Beats a Direct‑to‑PC Plug‑In

Most laptops and desktops have only a handful of high‑speed ports. When you start stacking external SSDs, HDDs, and a USB‑C flash drive, you quickly run out of space and risk throttling performance because the internal controller is shared across all devices. A powered hub solves both problems:

  • Power headroom – The included 65 W (20 V/3.25 A) adapter supplies enough juice to keep three or four 2.5‑inch drives running without draining your laptop’s battery.
  • Dedicated bandwidth – USB‑C 3.2 and the two USB‑A 3.2 ports each negotiate a full 10 Gbps lane, so a single large drive can transfer at its maximum speed while another drive backs up a different folder.
  • Cable organization – With a single 3.3‑foot cable reaching your desk, you avoid a spaghetti mess of cords behind the monitor.

Setting Up the Hub for Backup‑First Use

1. Choose Your Drives

Pick drives that match your backup strategy:

RoleRecommended Drive TypeReason
Primary archive (daily)2.5‑inch SSD (USB‑C 3.2)Fast writes, low power
Secondary archive (weekly)3.5‑inch HDD (USB‑A 3.0)High capacity, inexpensive
Off‑site sync (monthly)Portable USB‑C flash driveEasy to carry, fits in a drawer

Because the hub’s two PD ports are intended for phones or tablets, avoid plugging a laptop into them for power. They will charge a phone at up to 45 W, but they don’t provide enough stable output for a laptop’s charging curve.

2. Connect the Hub

  1. Plug the hub’s USB‑C 3.2 cable into a USB‑C port on your computer (preferably a dedicated 3.2 lane).
  2. Attach the 65 W power brick to the hub’s power input and plug it into a wall outlet.
  3. Connect each external drive to the appropriate port:
    • Use the USB‑C 3.2 ports for SSDs and flash drives that support the newer connector.
    • Use the USB‑A 3.2 ports for any high‑speed external HDDs that still have a USB‑A plug.
    • Reserve the USB‑A 3.0 ports for older drives that don’t need the full 10 Gbps bandwidth.

3. Verify Transfer Speed

Open your OS’s file explorer, copy a 1‑GB test folder to each drive, and watch the transfer rate. You should see speeds close to the drive’s rated performance; if a drive stalls at a few MB/s, double‑check that it’s plugged into a USB‑C 3.2 or USB‑A 3.2 port rather than a 3.0 port.

4. Choose Backup Software

Windows users can rely on File History or Macrium Reflect; macOS users can use Time Machine. All of these tools let you point to a specific external volume as the backup destination. For cross‑platform consistency, consider a third‑party solution like Duplicati or Restic, which can run scheduled jobs and encrypt the data.

5. Create a Backup Schedule

A sensible tiered schedule looks like this:

FrequencyWhat gets backed upDestination
Every hourCurrent project folderPrimary SSD (USB‑C 3.2)
Daily at 02:00 AMFull user profileSecondary HDD (USB‑A 3.2)
Weekly on SundayArchive of weekly snapshotsSame secondary HDD
MonthlyCompressed archive of the monthPortable flash drive (USB‑C)

Most backup utilities let you set these intervals in the preferences pane. The hub stays powered all night, so the computer can write to the drives without worrying about power loss.

6. Automate Drive Mounting (Optional)

If you prefer a “plug‑and‑play” experience, add a small script that runs at login:

#!/bin/bash
# macOS example – mount external volumes and start backup
diskutil mountDisk /dev/disk2   # Primary SSD
diskutil mountDisk /dev/disk3   # Secondary HDD
# Launch backup daemon
launchctl load /Library/LaunchDaemons/com.backup.daily.plist

Linux users can create a systemd service that watches /dev/sdX devices and triggers rsync jobs. The key is to let the hub stay on, so the script only needs to mount, not power up the drives.

Keeping Your Backup Hub Tidy

A hub with nine ports can become a cable jungle quickly. Here are two habits that keep the desk looking clean:

  • Label each drive with a short, color‑coded tag (e.g., “Daily SSD – Red”). The label helps you spot the right cable when you need to swap a drive for a larger one.
  • Route the hub’s power cable through a cable‑management sleeve or a desk grommet. The 3.3‑foot length is long enough to reach a wall outlet without pulling on the hub, but short enough to stay out of the way.

For more ideas on cable organization, see our guide on Standing Desk Cable Management.

Monitoring Health of Your Backup Drives

Even with a solid hub, drives can fail. Use these checks:

  • SMART status – Run smartctl -a /dev/sdX (Linux/macOS) or a third‑party GUI on Windows to see reallocated sector count and temperature.
  • Checksum verification – After each backup, run a quick md5sum or shasum on a sample file to confirm integrity.
  • Hub temperature – The aluminum unibody dissipates heat well, but if you notice the hub getting warm during long backup windows, give it a few minutes of breathing room.

If a drive starts showing warning signs, replace it before the next scheduled backup. The hub’s multiple ports make swapping a failing drive painless—just unplug the bad one and plug in the new one without rebooting the computer.

Potential Drawbacks

Power Limits on the PD Ports

The two USB‑C PD ports are limited to 45 W each and are optimized for charging phones or tablets. Trying to power a laptop or a power‑hungry external enclosure from these ports can cause the hub to throttle or shut down. Stick to the dedicated 65 W adapter for overall hub power and use the PD ports only for mobile devices.

Bandwidth Sharing on USB‑A 3.0 Ports

While the hub offers four USB‑A 3.0 ports, they share a single 5 Gbps bus. If you connect more than two high‑throughput drives to those ports simultaneously, you’ll see a noticeable dip in transfer speed. For any drive that you expect to write large backup sets to, prefer a USB‑C 3.2 or USB‑A 3.2 slot.

Real‑World Example: A Freelance Designer’s Workflow

Emma, a freelance graphic designer, works on a 27‑inch 4K monitor with a USB‑C dock. She added the intpw 9‑Port hub to her desk because her dock only had two spare ports. Her setup looks like this:

  • USB‑C 3.2 – 1 TB Samsung Portable SSD (daily project backup)
  • USB‑A 3.2 – 4 TB WD My Book (weekly full‑system backup)
  • USB‑A 3.0 – 2 TB Seagate Backup Plus (archival snapshots)
  • USB‑C PD – iPhone 15 (charging while she works)

She runs Duplicati with an hourly schedule for the SSD and a nightly schedule for the HDD. After a month, she reported zero missed backups and a tidy desk with only one cable running from the hub to the wall. The hub’s aluminum body also matched the aesthetic of her minimalist workspace.

FAQ‑Style Quick Tips (Not a Formal FAQ Block)

  • Can I use the hub with a desktop PC? Absolutely – just connect the hub’s USB‑C cable to any USB‑C 3.2 header on the motherboard or to a front‑panel USB‑C port. The power adapter will still supply the necessary current for external drives.
  • Do I need additional software to make the hub “smart”? No. The hub is a passive device; all scheduling and automation happen in the backup software you choose.
  • Is the hub safe for 24/7 operation? The aluminum chassis dissipates heat well, and the built‑in power management of modern SSDs/HDDs means they can stay powered continuously without issue.

Wrap‑Up

Using the intpw 9‑Port USB 3.2 Hub as a backup hub is a straightforward way to centralize storage, keep your data safe, and maintain a clean desk. By allocating the faster USB‑C and USB‑A 3.2 ports to the drives that need the most bandwidth, powering the hub with its 65 W adapter, and setting up a tiered backup schedule, you get a “set‑and‑forget” system that works for any home‑office workflow.

For deeper troubleshooting tips, check out our article on USB Hub Troubleshooting: Fix Connectivity, Speed, and Power Issues in Your Home Office. If you’re still deciding which hub to buy, the comparison of aluminum versus plastic builds can give you more context on durability and heat handling: Aluminum vs Plastic USB Hubs for a Desk Setup.